NIST logo

Publications Portal

You searched on:
Topic Area: Manufacturing

Your search results exceeded 1,000 records. Please refine your search and try again.
Displaying records 1 to 10 of 1000 records.
Resort by: Date / Title


1. Towards a Domain-Specific Framework for Predictive Analytics in Manufacturing
Topic: Manufacturing
Published: 10/3/2014
Authors: David Jacques Antoine Lechevalier, Anantha Narayanan Narayanan, Rachuri Rachuri
Abstract: Data analytics is proving to be very useful for achieving productivity gains in manufacturing. Predictive analytics (using advanced machine learning) is particularly valuable in manufacturing, as it leads to production improvement with respect to the ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=916274

2. Obstacle Detection and Avoidance from an Automated Guided Vehicle
Topic: Manufacturing
Published: 9/18/2014
Authors: Roger V Bostelman, William P Shackleford, Geraldine S Cheok
Abstract: Current automated guided vehicle (AGV) technology typically provides material handling flow along single or dual opposing-flow lanes in manufacturing and distribution facilities. An AGV stops for most any obstacle that may be in its path which then ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915448

3. Non-destructive Measurement of the Residual Stresses in Copper Through-Silicon Vias using Synchrotron Based Micro-beam X-ray Diffraction
Topic: Manufacturing
Published: 7/1/2014
Authors: Chukwudi Azubuike Okoro, Lyle E Levine, Yaw S Obeng, Klaus Hummler, Ruqing Xu
Abstract: In this study, we report a new method for achieving depth resolved determination of the full stress tensor in buried Cu through-silicon vias (TSVs), using synchrotron based X-ray micro-diffraction technique. Two adjacent Cu TSVs were analyzed; on ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915348

4. Effects of Temperature on Surface Accumulation and Release of Silica Nanoparticles in an Epoxy Nanocoating Exposed to UV Radiation
Topic: Manufacturing
Published: 6/16/2014
Authors: Chun-Chieh Tien, Ching-Hsuan Chang, Bernard Hao-Chih Liu, Deborah L Stanley, Savelas A Rabb, Lee Lijian Yu, Tinh Nguyen, Li Piin Sung
Abstract: Polymer nanocoatings are increasingly used outdoors and in harsh environments. However, because most common polymers degraded by the weathering elements, nanoparticles in polymer nanocoatings may be released into the environments. Such nanoparticle r ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915955

5. Uncertainty in Measurement of the Maximum Cutting Tool Temperature by Infrared Thermography
Topic: Manufacturing
Published: 6/13/2014
Authors: Brandon M Lane, Eric Paul Whitenton, Viswanathan Madhavan, M Alkan Donmez
Abstract: This paper presents an analysis of the uncertainty in measurement of the peak temperature on the side face of a cutting tool by infrared thermography. An analytical method uses the temperature measurement equation to study the uncertainty arising f ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915534

6. Infrared Thermography of the Chip-Tool Interface through Transparent Cutting Tools
Topic: Manufacturing
Published: 6/2/2014
Authors: Thejas T. Menon, Viswanathan Madhavan
Abstract: In-situ observation of the chip-tool interface has been carried out while machining Ti-6Al-4V. A low-noise camera sensitive to visible and near infrared (IR) radiation has been used to record the radiation emitted by the interface, and relatively lon ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915381

7. A portrait of an ISO STEP tolerancing standard as an enabler of smart manufacturing systems
Topic: Manufacturing
Published: 5/21/2014
Authors: Allison Barnard Feeney, Simon Paul Frechette, Vijay Srinivasan
Abstract: The International Organization for Standardization (ISO) has just completed a major effort on a new standard ISO 10303-242 titled ,Managed Model Based 3D Engineering.‰ It belongs to a family of standards called STEP (STandard for the Exchange of Prod ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=915430

8. 2D and 3D Topography Comparisons of Toolmarks Produced from Consecutively Manufactured Chisels and Punches.
Topic: Manufacturing
Published: 5/20/2014
Authors: Xiaoyu A Zheng, Johannes A Soons, Robert Meryln Thompson, John Villanova, Taher Kakal
Abstract: A 2009 report by the National Academies [1] recommended strengthening the scientific basis of procedures and criteria employed by the forensic science specialty of toolmark identification. The current method of comparison and determination of ide ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=914887

9. Geometric Interoperability via Queries
Topic: Manufacturing
Published: 5/19/2014
Author: Vijay Srinivasan
Abstract: The problem of geometric (model and system) interoperability is a non-trivial generalization of the classical problem of part interchangeability in mechanical assemblies. Interoperability subsumes the challenging problems of geometric model quality, ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=914283

10. Report from a 2013 ASME Panel on Geometric Interoperability for Advanced Manufacturing
Topic: Manufacturing
Published: 5/19/2014
Authors: Vijay Srinivasan, Vadim Shapiro
Abstract: During the Summer of 2013 in a conference organized by the American Society of Mechanical Engineers (ASME) at Madison, Wisconsin, a panel of academic, industrial, and government researchers engaged in a spirited discussion on the issue of geometric i ...
http://www.nist.gov/manuscript-publication-search.cfm?pub_id=914694



Search NIST-wide:


(Search abstract and keywords)


Last Name:
First Name:







Special Publications:

Looking for a NIST Special Publication (NIST SP Series)? Place the series number and dash in the report number field (Example: 800-) and begin your search.

  • SP 250-XX: Calibration Services
  • SP 260-XX: Standard Reference Materials
  • SP 300-XX: Precision Measurement and Calibration
  • SP 400-XX: Semiconductor Measurement Technology
  • SP 480-XX: Law Enforcement Technology
  • SP 500-XX: Computer Systems Technology
  • SP 700-XX: Industrial Measurement Series
  • SP 800-XX: Computer Security Series
  • SP 823-XX: Integrated Services Digital Network Series